Water Eject: Free Online Water Eject Sound
Got water in your phone speaker? Press play below. Our 165 Hz water eject sound vibrates the speaker cone to push trapped droplets out of the grille — free, instant and right in your browser.
How to eject water from your speaker in 4 steps
- Take off the case and wipe the outside of the phone with a lint-free cloth.
- Turn the volume to maximum and switch off silent / Do Not Disturb mode so the tone actually plays through the speaker.
- Point the speaker grille downwards, so gravity helps the droplets fall out rather than run deeper inside.
- Press play on Water Eject and let the cycle finish. Repeat two or three times if the sound is still muffled, then try Deep Clean.
You will often see tiny droplets on the grille or the table after the first run. That is the water eject sound doing its job.
What is the water eject sound?
The water eject sound is a low-frequency tone — usually around 165 Hz — played at high volume through a wet speaker. At that frequency the speaker cone moves back and forth with its largest excursion, pumping air through the grille like a tiny bellows. The pressure pulses break the surface tension that keeps a droplet stuck in the mesh, and the droplet is pushed out.
Apple Watch has done this for years with its built-in Water Lock feature, and the popular iPhone “Water Eject” Siri Shortcut uses the same idea. This page gives you the same sound on any device with a browser: iPhone, Android, Samsung Galaxy, iPad, Windows laptops, MacBooks and even Bluetooth speakers.
Why 165 Hz works better than a random tone
- Low frequencies move more air. A 165 Hz wave forces the cone to travel much further than a 1,000 Hz tone at the same volume, so each pulse carries more energy.
- Small phone speakers still reproduce it. Go much lower (below ~100 Hz) and most phone speakers simply cannot play it, so nothing moves.
- Pulsing beats a steady tone. Our engine modulates the wave so pressure arrives in bursts, which is far better at dislodging a stuck droplet than constant pressure.
- A short sweep catches every droplet size. After the main tone, the cycle sweeps through other frequencies because different droplets respond best to different frequencies.
Want the full physics? Read speaker cleaner frequencies explained.
Signs you have water in your phone speaker
- Music, videos and calls sound muffled, quiet or “underwater”.
- You hear crackling, buzzing or distortion at higher volumes.
- The sound improves slightly when you shake the phone or hold it grille-down.
- Your phone shows a liquid detected or moisture detected warning on the charging port at the same time.
Water eject on iPhone, Android and other devices
The tool above works in Safari, Chrome, Edge, Firefox and Samsung Internet. For device-specific tips, use the guide for your device:
- iPhone water eject — bottom speaker and the top earpiece speaker
- Android water eject — Pixel, OnePlus, Xiaomi, Oppo, Vivo and Realme
- Samsung Galaxy water eject
- AirPods water eject and Apple Watch water eject
- Laptop speakers and Bluetooth speakers
Water eject vs. rice vs. shaking the phone
Rice does not pull water out of a speaker chamber — it mostly leaves dust and starch in the ports, and Apple itself advises against it. Shaking helps a little but cannot generate the rapid pressure pulses that a 165 Hz tone does. Heat (hair dryers, radiators) can warp the speaker membrane and adhesives. A water eject sound, followed by air-drying grille-down for a few hours, is the safest at-home approach.
When water eject is not enough
Sound waves clear water from the speaker grille and chamber. They cannot repair corrosion, a damaged circuit board or a phone that was submerged in salt water, soda or chlorinated pool water for a long time. If the speaker is still muffled after a full night of drying and several cycles, or the phone will not power on properly, switch it off and see a repair shop. Our water damaged phone speaker rescue guide walks through the full sequence.
Frequently asked questions
Does the water eject sound really work?
Yes, for water sitting in the speaker grille and the small chamber behind it. The 165 Hz tone makes the speaker cone pump air in strong pulses, which pushes droplets out. It cannot fix internal corrosion or electronic damage.
How many times should I play the water eject sound?
Run the cycle two or three times, with the speaker facing down. If the sound is still muffled, let the device air-dry for a few hours and run it again.
Is the water eject sound safe for my speaker?
Yes. 165 Hz is well within the range every phone speaker is designed to play. Avoid running it for many minutes non-stop at maximum volume; short cycles are all you need.
Do I need to download a water eject app?
No. The tool runs in your web browser, so there is nothing to install. If you prefer an app, see our speaker cleaner app options.
Can I use water eject on the earpiece speaker?
Yes. Use our earpiece speaker cleaner, which routes the sound to the top call speaker where possible and explains how to target it.
Related free tools
Still need help?
hassan@zavify.co.uk